Kerala PSC Assistant Executive Engineer Syllabus 2022 & Exam Pattern PDF Download

Kerala PSC Assistant Executive Engineer Syllabus 2022 & Exam Pattern PDF Download: Get both the Kerala PSC Assistant Executive Engineer Syllabus 2022 and the Kerala PSC Assistant Executive Engineer Exam Pattern 2022 details from the this page. Also, the direct link to get the Kerala PSC Assistant Executive Engineer Exam Syllabus 2022 is attached at the end of the page. So, applied candidates can make use of the PDF link and save it to your device. Also, get the detailed exam pattern from the below sections. Check the subject wise Kerala PSC Assistant Executive Engineer Mechanical Syllabus 2022 and the Kerala PSC Assistant Executive Engineer Civil Syllabus 2022 topics furnished in the further sections.

Get a brief outline of the Exam Pattern from here. The Officials of the Kerala PSC will conduct the exam for about 100 Marks. There will be 2 Parts in the exam for the post of the Assistant Executive Engineer. Part I contains of 50 Questions from Civil Engineering for 50 Marks. And, Part II contains of 50 questions from Mechanical Engineering for 50 Marks. The type of questions asked are multiple choice objective type. The Total time duration is 1 Hour 30 Minutes.

Kerala PSC Assistant Executive Engineer Syllabus 2022 – Details

Kerala PSC Assistant Executive Engineer Syllabus 2022 & Exam Pattern PDF Download
Name of the OrganizationKerala Public Service Commission (Kerala PSC)
Posts NameAssistant Executive Engineer
CategorySyllabus
Job LocationKerala
Official Websitekeralapsc.gov.in

Kerala PSC Assistant Executive Engineer Exam Pattern 2022

The Kerala PSC Assistant Executive Engineer Exam Pattern 2022 is given below in the form of a table. By knowing the complete details of the Exam Pattern and practice all subject topics in the Pattern, candidates can give their best in the exam. Candidates can also gain the highest marks in the examination by practicing all Kerala PSC Assistant Executive Engineer Civil Syllabus 2022 and the Kerala PSC Assistant Executive Engineer Mechanical Syllabus 2022 given in the below sections.

PartName of the SubjectTotal Marks
Part I: Civil EngineeringMechanics of Solids and Structural Analysis7 marks
Fluid Mechanics and Water Resources Engineering7 marks
Surveying and Levelling, Quantity Surveying and Valuation7 marks
Building materials, Construction Technology, Construction Management7 marks
Environmental Engineering7 marks
Design of Structures5 marks
Geotechnical Engineering5 marks
Transportation Engineering and Urban Planning5 marks
Part II: Mechanical EngineeringEngineering Mechanics7 marks
Mechanics of Solids7 marks
Mechanics and Dynamics of Machinery12 marks
Fluid Mechanics and Heat Transfer12 marks
Industrial and Production Engineering12 marks
Total Marks100 Marks
Duration: 1 Hour 30 Minutes
Objective Multiple Choice Questions

Download Kerala PSC Assistant Executive Engineer Syllabus 2022 PDF

Candidates must prepare all the topic wise Kerala PSC Assistant Executive Engineer Syllabus 2022. The syllabus topics for both the Civil Engineering and Mechanical Engineering are given in the below. Prepare well for the exam in order to gain the complete knowledge on all subjects. And, attain the post of the Assistant Executive Engineer in the organization of the Kerala Public Service Commission. Also get the PDF from the bottom of the page.

Civil Engineering

Mechanics of Solids and Structural Analysis

Concept of stress and strain, Bending moment and shear force, Stresses in beams, Deflection of beams, Theory of columns, Truss analysis, Displacement response of statically determinate structural systems using energy methods, Principle of virtual work, Statically indeterminate structures, Strain Energy methods, Moving loads and influence lines, Arches. Slope Deflection Method, Moment Distribution Method, Clapeyrons Theorem (Three Moment Equation), Kani’s method of analysis.

Fluid Mechanics and Water Resources Engineering

  • Fluid Statics – Fluid pressure, Buoyancy and floatation, Fluid Kinematics, Dynamics of fluid flow, Flow through orifice and notches, Flow through pipes, Boundary layer, Drag and Lift on immersed bodies.
  • Hydraulic machines – flow through vanes (moving and stationary) Impulse and reaction Turbines, Centrifugal Pumps, Open channel flow, Uniform flow, Hydraulic Jump, Gradually varied flow, Dimensional analysis and model testing. Hydrologic cycle, Precipitation, Infiltration and Evaporation-measurement and data analysis. Runoff-components and computation, Hydrograph, Unit Hydrograph and S Hydrograph.
  • Irrigation types and methods -Soil water plant relationships, Frequency of irrigation, Computation of crop water requirement. Stream flow measurement -Stage discharge curve. Meandering of rivers, river training works.
  • Surface water systems: diversion and storage systems, reservoir – estimation of storage capacity and yield of reservoirs – reservoir sedimentation -useful life of reservoir. Groundwater – Aquifer types and properties – Steady radial flow into a well. Estimation of yield of an open well.

Surveying and Levelling, Quantity Surveying and Valuation

  • Basics of Surveying, Levelling and Contouring, Area and Volume Computation, Theodolite Survey, Mass Diagram, Triangulation, Theory of Errors, Electronic Distance Measurement, Total Station Survey, Global Positioning Systems, Remote Sensing, Geographical Information System
  • Analysis of rates – Data book and schedule of rates, Analysis of rates for various items of
    work, Detailed specification. Types of Estimate. Detailed estimate including quantities, abstract and preparation of various items of works, Preparation of bar bending schedules for various RCC works. Valuation- Methods of valuation, Depreciation, Fixation of rent.

Building materials, Construction Technology, Construction Management

  • Construction Materials – Timber, Mortar, Iron and Steel, Structural steel, Modern materials. Concrete–Admixtures, Making of concrete, Properties of concrete, Mix proportioning.
  • Building construction- Foundations, Cost-effective construction, Masonry, Lintels and
    arches. Floors and flooring, Roofs and roof coverings, Doors, windows and ventilators,
    Finishing works. Tall Buildings – Steel and Concrete frame, Prefabricated construction,
    Slip form construction. Vertical transportation – Stairs, Elevators, Escalators and Ramps.
    Building failures and Retrofitting, failures in RCC and Steel structures.
  • Construction Planning and Scheduling, Construction disputes and settlement, Ethics in
    Construction, Construction safety, Principles of materials management, Quality
    management practices, Construction procedures.

Environmental Engineering

  • Water sources and demand, Quantity estimation, Population forecasting, Quality of water. Water treatment- Physical methods, Chemical methods. Design of sedimentation tank, flocculator, clariflocculator, filters, Membrane treatment techniques. Disinfection methods. Distribution of water, Pumps, Hardy Cross method of analysis
  • Waste water- Sources, Characteristics, Oxygen demand. Design of sewers, Circular
    sewers, Partial flow and full flow conditions. Sewer appurtenances, Disposal of waste water, Streeter Phelps equation, Oxygen sag curve, Treatment methods, Aerobic and
    anaerobic methods, Design of various treatment units-Screening, Grit chamber, Sedimentation tank, Activated Sludge process, Trickling filter, Rotating biological
    contactor, Septic tanks, Imhoff tanks, Oxidation ditches, Oxidation ponds, Up flow
    anaerobic sludge blanket reactors, Sludge digestion, Sludge drying bed.
  • Air pollution sources, effects on human, Control of air pollutants, Air quality legislations.

Design of Structures

  • Limit state method of design, Analysis of reinforced rectangular beams, Shear strength of RC beam, Design of shear reinforcement, Bond and development length, Curtailment of reinforcement, Design for torsion, Design of one way slab, Cantilever slab, Continuous
    slab (detailing only), Two way slabs, Limit state of serviceability, Deflection, Cracking, Stair cases -design & detailing. Columns-effective length-design of axially loaded short
    columns with rectangular ties and helical reinforcement.
  • Columns subjected to compression, Uniaxial bending and biaxial bending, Design of
    slender columns, Design of wall/strip footing- design of footings, Design of cantilever
    retaining wall without surcharge, design principles of counter fort retaining wall, Circular
    slabs simply supported, fixed and partially fixed subjected to udl, Design of water tanks,
    Design philosophy and requirements, joints, IS code recommendations, Pre-stressed
    concrete, Concept of prestressing, materials and methods of prestressing, Prestressing
    systems, losses of prestress, Analysis of prestressed beams (rectangular and I-sections) at stages of transfer and service
  • Steel and steel structures – Bolted and welded connections, Tension members,
    Compression members, Beams, Roof trusses, Purlins. Timber structures- columns,
    composite beams (concepts only)

Geotechnical Engineering

  • Major soil deposits of India, Classification and three phase system of soil, Permeability of
    soils, Principle of effective stress, Shear characteristics of soil, Consolidation (Terzaghi’s
    theory of one-dimensional consolidation only) and Compaction.
  • Stability of finite slopes-Swedish Circle Method and Friction circle method, Stresses in
    subsoil due to loaded areas of various shapes, Boussinesq’s formula, Newmark’s chart
  • Lateral earth pressure-Rankine’s and Coulomb’ theories Bearing capacity of soil, Estimation of magnitude of settlement, Site investigation, Standard Penetration Test and Plate load test, Design of shallow, deep and machine foundations, Ground improvement techniques.

Transportation Engineering and Urban Planning

  • Classification and alignment of highways, Geometric design of highways, Properties and
    testing of pavement materials, CBR method of flexible pavement design, Construction and maintenance of pavements, Design of runways, taxiways and aprons.
  • Traffic characteristics- Traffic studies and analysis, Traffic control devices. Airport characteristics Aircraft component parts. Site selection, Terminal area planning- Airport marking and lighting.
  • Traffic regulation rules, Highway capacity, Traffic safety, Influencing factors and preventive measures for traffic accidents, Basic diagrams of traffic flow theory. Railways geometric design of tracks, railway operation control, Maintenance. Alignment, Ventilation and drainage of tunnels, Types of harbour and docks.
  • Goals and objectives of planning; Components of planning, Regional planning, Theories of urbanization, Study of Urban Forms, Zoning, Development of new towns, Town Development Plan, Town planning acts.

Mechanical Engineering

MODULE – I (ENGINEERING MECHANICS)

Statics: Fundamental concepts and laws of mechanics, Rigid body, principle of
transmissibility of forces, Coplanar force systems, moment of a force, principle of moments, resultant of force and couple system, Equilibrium of rigid body, free body diagram, conditions of equilibrium in two dimensions, two force and three force members.

MODULE – II (MECHANICS OF SOLIDS)

Material behavior, uniaxial tension test, stress-strain diagrams, concepts of orthotropy,
anisotropy and inelastic behavior, Hooke’s law for linearly elastic isotropic material under
axial and shear deformation, Definition of stress and strain at a point (introduction to stress
and strain tensors and its components only), Poisson’s ratio, biaxial and triaxial deformations, Bulk modulus, Relations between elastic constants.

MODULE – III (MECHANICS AND DYNAMICS OF MACHINERY) 

  • Gears, terminology of spur gears, law of Gearing, involute spur gears involutometry,
    contact ratio, interference, backlash, gear standardization, inter changability, centre distance modification, modes of gear tooth failures, theory and details of bevel, helical and worm gearing.
  • Introduction to vibrations, free vibrations of single degree freedom systems, Energy
    Method, Undamped and damped free vibrations, viscous damping, critical damping,
    logarithmic decrement, Coulomb damping, harmonically excited vibrations, Response of
    an undamped and damped system, transmissibility.

MODULE – IV (FLUID MECHANICS AND HEAT TRANSFER) 

  • Introduction: Fluids and continuum, Physical properties of fluids, density, specific weight,
    vapour Pressure, Newton’s law of viscosity. Ideal and real fluids, Newtonian and non Newtonian fluids.
  • Modes of Heat Transfer, Conduction, Fourier law of heat conduction, Thermal conductivity
    of solids, liquids and gases, Factors affecting thermal conductivity, Most general heat
    conduction equation in Cartesian, cylindrical and spherical coordinates, One dimensional
    steady state conduction with and without heat generation, conduction through plane walls, cylinders and spheres, variable thermal conductivity conduction shape factor, heat transfer through corners and edges. Critical radius of insulation.

MODULE – V (INDUSTRIAL AND PRODUCTION ENGINEERING)

  • Management of Human Relations in Organisations: Ethics and fair treatment at work,
    ethics and the law, ethics fair treatment and justice. Ethical behaviour at work, individual factors, organizational factors, the boss’s influence, ethics policies and codes, the organization’s culture, role of HR in fostering ethics and fair treatment. Disciplining an employee, formal disciplinary appeals process, discipline without punishment, employee privacy.
  • Sand Casting: Sand Molds, Types of Molding Sands and Testing Type of patterns, Pattern
    Materials, Cores, Types and applications, Sand Molding Machines Gating System, Risering Shell Mold Casting, Ceramic Mold Casting, Investment Casting, Vacuum
    Casting, Slush Casting, Pressure Casting, Die Casting, Centrifugal Casting, Design
    Considerations based on Various Shapes, Defects in Castings, simple problems in casting
Kerala PSC Assistant Executive Engineer Syllabus 2022 – Important Link
Download Kerala PSC Assistant Executive Engineer Syllabus 2022 & Exam Pattern PDFClick Here

I Hope, the Kerala PSC Assistant Executive Engineer Syllabus 2022 details given above are useful for all the applicants. To check more updated information like this, keep in touch with us @ Freshersnow.com.

★★ You Can Also Check ★★
Kerala PSC Assistant Executive Engineer Hall TicketKerala Employment News
Kerala Govt JobsKerala PSC Recruitment